Toytec Boss 2.5 Aluma Series Performance Suspension System for 05-23 Tacoma

25BOSSTACP-ALM – Toytec Boss 2.5 Aluma Series Performance Suspension System for 2005-Current Tacoma

This kit is designed with performance in mind.

25BOSSTACP-ALM Includes:

Front Coilovers:

• Choose from Toytec Boss 2.5 Front Aluma Series IFP Coilovers or 2.5 Aluma with Remote Reservoirs
  • Aluma 2.5 shock bodies are made from hard anodized aluminum for cooler operation as well as better protection from the elements.
  • Adjustable from 2-3″ of lift. (Maximum ride height of 23″ center of hub to fender)
  • Internal hydraulic valving optimized to match the 700 lb rate spring for use with or without a bumper or winch.
  • Coilovers are assembled and ready to bolt on.  No spring compressor or special tools needed for installation.
  • Aluma Series shock bodies are 2.5″ in diameter providing additional oil over standard OEM shocks.
  • This 2005-current Tacoma kit includes sway bar relocation brackets, preload adjustment tool and owner’s manual.
  • Nitrogen charged design with internal floating piston to help prevent shock fading and cavitation
  • Heavy duty 19mm induction-hardened piston shaft.
  • These shocks are fully rebuildable

Front Differential Drop kit – Recommended for all lifted 4x4s

Front Bump Stops:

• DuroBumps are proudly made in the USA with dual durometer (hardness) rubber that provides smooth progressive dampening and greatly reduces hard bottom outs. This allows for more control and comfort compared to OEM bump stops that are harsh on contact. With DuroBumps installed, the shell-shock effect experienced when hitting the OEM bump stops is completely eliminated.

Ubolts:  Choose from standard 7.5″ ubolts or our ubolt flip kit.  The ubolt flip kit will allow you to turn your ubolts facing upward, providing additional ground clearance.

Rear Bump Stops:

• Rear Bump Stop Extension kit- 43007 – Recommended for use with add-a-leafs or complete leaf spring packs, these will allow your factory rear bump stops to function with the lift.  (*Requires drilling 2 holes per side).
• Durobumps – Tacoma rear bump stops eliminate the shell shock effect we’re all familiar with when hitting OEM bump stops. Our dual durometer bump stops easily absorb hard impacts and help keep the vehicle stable at higher speeds in rough conditions. The 4.25″ rear bump stop is intended for trucks with a rear lift of 2″ and extended shocks of up to 1″. These bump stops have been designed to stop wheel up travel under articulation prior to extended shocks bottoming out.  Can be used with or without the Ubolt flip kit.

Rear Shocks:

• TACBOSS25R-ALM – Toytec Boss 2.5 Aluma Series Rear Shocks.
  • Perfectly matched to pair with the Boss Aluma Series Coilovers
  • Tuned for maximum performance and comfort.
  • Gas-pressurized design with internal floating piston to help prevent cavitation and fading
  • The shock bodies are 2.5″(56mm) made from hard anodized aluminum for cooler operation as well as better protection from the elements.
  • TACBOSS25R-ALM are completely rebuildable, serviceable and tunable.
• LKTAC20R-P – Toytec 2.0 Aluma Series IFP Rear Shocks 
  • Similar to the 2.5 IFP Aluma shocks, but in a 2.0 Diameter.

Add Upper Control Arms to complete your Tacoma suspension kit (Recommended for use with Aluma Series Coilovers):

• Total Chaos Uniball Upper Control arms – 96504 – Maximize your wheel travel and increase your strength while also correcting alignment angles.
• SPC Adjustable Upper Control Arms – 25470 – The most adjustable UCA on the market.  Correct your alignment angles.  Also, great to help with adjusting for tire clearance.
• Nitro Gear Extended Travel Ball Joint Style Upper Control Arms – NPUCA-TACO – Built in additional caster to correct alignment.  Heavy duty Grease-able sealed ball joint for low maintenance and quiet operation.